CCNA Final exam 4 考试题及答案
[b]来源版块: [/b][url=http://bbs.51cto.com/forum-144-1.html][color=Red]网络工程师[/color][/url][b]压缩包内文件格式:[/b] 文本内容
[b]附件来源:[/b] 原创
[b]运行平台:[/b] Windows平台
[b]是否经本人验证:[/b] 是
[b]附件性质:[/b] 共享
[b]详细说明:[/b] CCNA Final exam 4 考试题及答案 A卷和B卷补考都有，85%以上人正确率，由于答案有特殊符号不能贴出来。
这是A卷，不下载可以直接复制了
1
Refer to the exhibit. A network administrator is checking the status of router RTR_2. What is the most likely reason for the current status of the serial link to RTR_1?
*A cable has become disconnected.
The circuit is experiencing excessive RFI.
Authentication is not properly configured on the routers.
The routers are configured for different WAN encapsulations.
The clock rate is not properly configured on one of the routers.
2
While testing a new network design in the lab, a network administrator is configuring a serial link that connects two routers back-to-back. In order to finish the configuration, the administrator needs to identify which router is connected to the DCE end of the cable. What command can be issued to provide this information?
router# show status serial 0/0
*router# show controllers serial 0/0
router# show protocols serial 0/0
router# show version
router# show interfaces serial 0/0
3
Which statements are correct about the point in the network where the responsibility of the service provider ends? (Choose three.)
*The International point is on the customer side of the network terminating unit(NTU).
*The United States point is at the interface of the customer-provided equipment and the local loop.
The responsibility for this point is controlled by IANA.
*The point is called the demarcation point.
The point is typically located at the service provider's central office.
The point is located between the customer's local area networks.
4
A system administrator must provide Internet connectivity for 25 hosts at an insurance agency. The ISP has assigned two public IP addresses to this company. What can the administrator do to provide Internet access to all 25 users at the same time?
*Configure the router with dynamic NAT with PAT.
Configure the router with dynamic NAT for 25 users.
Configure the router with DHCP and static NAT.
Configure the router with static NAT for all 25 users.
This cannot be done with only two public addresses.
5
A system administrator is unable to ping the Serial0/0 interface of RouterB from RouterA. During the troubleshooting process, the following facts are established: - IP addressing and subnet masks are correct. - RouterA is a Cisco router and RouterB is a router from another vendor. - RouterA is configured with the default encapsulation. - The serial interfaces on both routers are up. - The protocol is down on the serial interfaces of both routers. What should the administrator do to solve the problem?
Add a clock rate on RouterA.
Enable the serial interface on RouterB.
*Change the encapsulation on both routers to PPP.
Connect the serial cable to the correct interface on RouterB.
Use the correct serial cable to attach the CSU/DSU to RouterB.
6
A network administrator must provide WAN connectivity between the Central office and three remote sites: East Branch, West Branch, and Remote. The East Branch and West Branch offices receive sales orders and transmit shipping confirmations to the Central office consistently throughout the day. The Remote office is staffed by one salesperson who travels through the northwestern territory. The salesperson occasionally needs to connect to the Central office for e-mail access. How should the network administrator connect these sites to the Central office? (Choose two.)
Connect the East Branch and West Branch remote offices with ISDN connections.
*Connect the East Branch and West Branch offices with Frame Relay connections.
Connect the East Branch and West Branch offices with POTS dial-up connections.
Connect the Remote office with a Frame Relay connection.
Connect the Remote office with an ISDN connection.
*Connect the Remote office with a POTS dial-up connection.
7
A system administrator needs to configure the regional office with ISDN for DDR connections to three remote sites. Each remote site requires different IP subnets, different encapsulations, and different authentication methods. The sites will not be connected at the same time. The company would like to accomplish this in the most cost effective manner. What method can the system administrator use to accomplish this task using the fewest B channels?
Install and configure a PRI.
Install and configure a BRI interface with separate SPIDs for each remote site.
Install and configure a BRI with multiple switch types in global configuration.
*Install and configure a BRI using dialer profiles.
Install and configure a separate BRI for each remote site.
8
A network administrator is having difficulty in establishing a serial link between a Cisco router and a router from another vendor. Both routers are configured for HDLC encapsulation. Which statements are true regarding this configuration? (Choose two.)
*The Cisco HDLC frame uses a proprietary "Type" field that may not be compatible with equipment of other vendors.
HDLC requires a clock rate to be configured on the routers at both ends of the serial link.
*PPP encapsulation is recommended for serial links between equipment from multiple vendors.
Usernames must be configured at both ends of the HDLC serial link.
The HDLC vendor type must be enabled on the Cisco router.
There is a mismatch in the HDLC authentication password configurations.
9
Which of the following is the order for the three phases of establishing a PPP serial link with authentication?
authentication, link-establishment, network layer protocols
authentication, network layer protocols, link-establishment
network layer protocols, link-establishment, authentication
network layer protocols, authentication, link-establishment
*link-establishment, authentication, network layer protocols
link-establishment, network layer protocols, authentication
10
The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue explains why the link is unable to establish a PPP session?
The IP addresses must be on different subnets.
*The usernames are misconfigured.
The passwords must be different for the CHAP authentication.
The clock rate must be 56000.
The clock rate is configured on the wrong end of the link.
Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
11
Refer to the exhibit. The link between the RTR-1 and RTR-2 routers is configured as shown in the exhibit. Although the show interfaces command shows the interface status as Serial0 is up, line protocol is up, IP traffic is not crossing this link. What is the problem?
The usernames are misconfigured.
The clock rate is configured on the wrong end of the link.
*The IP addresses are not in the same subnet.
Interface serial 0/0 on RTR-1 must connect to interface serial 0/1 on RTR-2.
The passwords must be different for the CHAP authentication.
The clock rate must be 56000.
12
A technician enters the interface serial 0/0.1 multipoint command when configuring a router. What effect will the multipoint keyword have in this configuration? (Choose two.)
*Split-horizon issues will need to be resolved for this network if RIP is the routing protocol.
A subinterface will be defined for each PVC.
*All the participating interfaces of remote routers will be configured in the same subnet.
A single DLCI will be used to define all the PVCs to the remote routers.
An IP address will need to be configured on the main interface.
13
Which router command would be used to associate a Layer 2 address with the corresponding Layer 3 address in the internetwork in the diagram?
RouterA(config-if)#frame-relay pvc 100 192.168.15.2
RouterA(config-if)#dialer-map ip 192.168.15.1 100 broadcast
*RouterA(config-if)#frame-relay map ip 192.168.15.2 100 broadcast
RouterA (config-if)#dialer-map 192.168.15.1 101 serial 0 broadcast
RouterA (config-if)#frame-relay dlci 101 192.168.15.1 broadcast
RouterA (config-if)#dialer-map 192.168.15.1 inverse-arp broadcast
14
Refer to the exhibit. Two routers are connected through a Frame Relay point-to-point PVC. The ILM-5 router is from a vendor other than Cisco. Which interface command is required to configure the link between the Cisco ILM-3 router and router ILM-5?
ILM-3(config-if)# encapsulation frame-relay cisco
ILM-3(config-if)# frame-relay pvc multipoint
*ILM-3(config-if)# encapsulation frame-relay ietf
ILM-3(config-if)# frame-relay lmi-type ansi
ILM-3(config-if)# frame-relay pvc point-to-point
15
What does the output of the show frame-relay map command shown below represent? (Choose two.) Serial 0 (up): ip 172.30.151.4 dlci 122, dynamic, broadcast, status defined, active
*172.30.151.4 represents the IP address of the remote router.
172.30.151.4 represents the IP address of the local serial interface.
DLCI 122 represents the interface of the remote router.
*broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC.
dynamic indicates that a dynamic routing protocol is enabled for this connection.
active indicates that the ARP process is working.
16
The output of the show interfaces serial 0/0 command for a frame-relay connection indicates that the serial line is up but the line protocol is down. What are possible causes for this? (Choose two.)
*There is an LMI-type mismatch between the Frame Relay switch and the router.
*There is no clock present on the serial interface.
The interface is shut down.
RARP is not functioning on the router.
The cable is disconnected.
17
What are two ways to resolve split-horizon issues in a Frame Relay network? (Choose two.)
*create a full-mesh topology
disable Inverse ARP
*use point-to-point subinterfaces
use multipoint subinterfaces
remove the broadcast keyword from the frame-relay map command
18
A network administrator issued the command show frame-relay pvc. The response from the router shows the status of a PVC as deleted. What is the reason for this output?
The DLCI is using the wrong LMI type.
The DLCI is usable but has little activity.
The DLCI is programmed in the switch but the circuit is not usable.
*The DLCI was formerly programmed in the switch but is no longer there.
19
When a Frame Relay switch detects an excessive buildup of frames in its queue, which of the following may occur? (Choose two.)
*Frames with the DE bit set are dropped from the switch queue.
Frames with the FECN and BECN bits set are dropped from the switch queue.
Frames in excess of the CIR are not accepted by the switch.
The switch sets the FECN bit on all frames it places on the congested link and sets the BECN bit on all frames it receives on the congested link.
*The switch sets the FECN bit on all frames it receives on the congested link and sets the BECN bit on all frames it places on the congested link.
20
What are two of the steps required to configure a router to connect over ISDN BRI? (Choose two.)
Configure the interface with a DLCI.
*Configure the SPIDs, if required by the ISDN switch.
Specify the the LMI type to be compatible with the CO switch.
Set the interface encapsulation to the Cisco or IETF frame type.
Configure a subinterface for each B channel.
*Set the switch type to work with the ISDN switch at the CO.
21
After the ISDN BRI interface is configured, which command can be used to verify that the router is communicating correctly with the ISDN switch?
show dialer
*show isdn status
show interfaces bri0/0:1
show interfaces serial0/0.1
22
Which of the following ISDN protocols is responsible for call setup and call teardown?
ITU-T Q.921
*ITU-T Q.931
ITU-T I.430
ITU-T I.431
23
Which protocol should be chosen to support WAN connectivity in a multi-vendor system and provide strong security through authentication?
NAT with DHCP
Frame Relay
HDLC with encryption
HDLC with CHAP
PPP with PAP
*PPP with CHAP
24
Which of the following describes the roles of devices in a WAN? (Choose three.)
*A CSU/DSU terminates a digital local loop.
A modem terminates a digital local loop.
A CSU/DSU terminates an analog local loop.
*A modem terminates an analog local loop.
*A router is commonly considered a DTE device.
A router is commonly considered a DCE device.
25
Which scenarios present possible reasons for using the frame-relay map command when configuring a Frame Relay connection? (Choose two.)
*when dynamic mapping of DLCIs to IP addresses is not supported by the remote router
when the local router is using IOS Release 11.1 or earlier
when the remote router is a non-Cisco router
when globally significant rather than locally significant DLCIs are being used
*when broadcast traffic and multicast traffic over the PVC must be controlled
26
Below is a list of DDR steps. Which of the following identifies the proper order of DDR? 1 - dial number is looked up2 - interesting traffic triggers DDR3 - route to destination is determined4 - call is made
1,2,3,4
1,3,2,4
2,3,1,4
2,1,3,4
*3,2,1,4
3,1,2,4
27
What causes a DDR call to be placed?
dial string
DLCI
idle time out
*interesting traffic
PVC
28
After configuring a dialup ISDN circuit, a network associate begins testing the dialup connection. When attempting to ping a host on the remote network, the local router does not attempt to dial the remote access server. Which of the following are possible errors in this configuration? (Choose three.)
PPP authentication is not properly configured.
*No dialer map is configured.
The ISDN circuit connected to the remote access server is busy.
*No interesting traffic is defined.
*No route is determined to the remote network.
A wrong number is configured in the dial string.
29
A branch office reports excessive connect time charges for an ISDN circuit used to connect to the regional office. Upon investigation of this issue, it is discovered that when an ISDN connection is initiated to the regional office it remains connected for an excessive amount of time. Which of the following configuration changes could be made to DDR on the router to reduce these connect time charges?
use PPP multilink
*lower idle timer setting
use CHAP authentication
change DDR from legacy to dialer profiles
30
An ISDN circuit from a branch office is remaining connected to the regional office. A network administrator determines a user has initiated a continuous ping from a desktop computer to the regional office. Which configuration change would allow the ISDN circuit to disconnect during any attempts to ping, while otherwise functioning properly?
change DDR from legacy to dialer profiles
remove the dialer list statement from the configuration
*change the dialer list to exclude ICMP as interesting
disable inverse ARP
31
What value in the address field of a Frame Relay header identifies the destination of the frame?
CIR
DE
*DLCI
ISDN
FRAD
PVC
32
Refer to the exhibit. The network administrator of the Denver router has determined that the DHCP clients on the network are not working properly. The clients are receiving IP configuration information from a DHCP server configured on the router but cannot access the Internet. From the output in the exhibit, what is the most likely problem?
The DHCP server service is not enabled.
The DHCP pool is not bound to the interface.
The inside interface for DCHP is not defined.
*The pool does not have a default router defined for the clients.
All the host addresses have been excluded from the DHCP pool.
Scoring Rule For: correctness of response
2 points for Option 4
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA 4 WAN Technologies
# 1.2.5 Configuring DHCP
33
Which circuit-switched WAN technology is often used to provide a backup for a leased line and additional capacity during peak usage times?
X.25
DSL
*ISDN
cable modem
34
A system administrator is troubleshooting a connectivity issue between two routers in a new installation. The administrator enters the debug ppp authentication command on the WHSE router. The graphic shows a part of the output received. From this output, what is the most likely cause of this connectivity issue?
There is not a route to the remote router.
The ISDN circuit on the remote router has failed.
*The username/password was not properly configured on the WHSE router.
The remote router has a different authentication protocol configured.
35
Which IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
172.55.16.0.16
*172.17.0.0/16
224.200.175.0/24
*192.168.168.0/22
*10.88.179.0/29
17.250.0.0/16
36
What is the purpose of the command marked with an arrow shown in the partial configuration output of a Cisco 806 broadband router?
defines which addresses are allowed out of the router
defines which addresses are allowed into the router
*defines which addresses can be translated
defines which addresses are assigned to a NAT pool
37
Refer to the exhibit. Which statements describe why the workstation with the IP address 192.168.89.99 cannot access the Internet? (Choose two.)
The NAT outside interface is not configured properly.
*The NAT inside interface is not configured properly.
The access control list does not include the IP address 192.168.1.99/28 to access the Internet.
The NAT pool is not properly configured to use routable outside addresses.
*The NAT pool is not properly configured to use the access control list for NAT.
38
Which of the following statements are correct regarding PAT? (Choose two.)
PAT is the best method to provide consistent global addresses for network servers.
PAT can only be configured to use one IP address, which is usually the IP address of the serial interface of the router.
PAT uses unique source port numbers on the inside local IP address to distinguish between translations.
*PAT uses unique source port numbers on the inside global IP address to distinguish between translations.
*When PAT is configured to use a pool of IP addresses and exhausts the ports of the first IP address, the router will move to the next available IP address.
39
How are the settings for ISDN switch type and SPIDs determined for a BRI interface configuration?
assigned by the network administrator
randomly, so long as they are not duplicated on the network
by trial and error
dynamically via Inverse ARP
assigned by IANA
*assigned by the service provider
40
When configuring a Frame Relay network with subinterfaces, which commands are configured on the subinterface? (Choose three.)
*frame-relay interface-dlci
encapsulation frame-relay ietf
*ip address
*frame-relay map
switch type 这是B卷，我整理了一下
1
Refer to the exhibit. A network administrator is checking the status of router CTL-1. What is the most likely reason for the current status of the serial link to CTL-2?
The circuit is suffering from excessive RFI.
Authentication is not properly configured on the routers.
The routers are configured for different WAN encapsulations.
The clock rate is not properly configured on one of the routers.
*A cable has become disconnected.
2
While prototyping an internetwork in the corporate lab, a network administrator is testing a serial link between serial 0/0 interfaces on two routers. The labels on the serial cable ends have been damaged and are unreadable. What command can be issued to determine which router is connected to the DCE cable end?
show interfaces serial 0/0
show version
*show controllers serial 0/0
show protocols serial 0/0
show status serial 0/0
3
Where in the network does the responsibility of the service provider end? (Choose three.)
*at the demarcation point
between the customer's local-area networks
*outside of the United States, on the customer side of the network terminating unit (NTU)
at the service provider's central office
*in the United States, the connection of the customer-provided equipment and the local loop
at the point in the network where NAT occurs
4
A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT for all ten users.
Configure dynamic NAT for ten users.
*Configure dynamic NAT with PAT.
Configure DHCP and static NAT.
What the administrator wants to do cannot be done.
5
Refer to the exhibit. A system administrator is unable to ping the S0 interface of the West router from the East router. During the troubleshooting process, the following facts are established: - IP addressing and subnet masks are correct. - East is a Cisco router and West is a router from another vendor. What should the administrator do to solve the problem?
Enable the serial interface on West.
*Change the encapsulation on both routers to PPP.
Add a clock rate on East.
Replace the serial cable used to attach the CSU/DSU to West.
Set the loopback interface on East.
6
A network administrator must provide WAN connectivity between a central office and three remote sites: Orlando, Atlanta, and Phoenix. The Orlando and Atlanta remote offices receive sales orders and transmit shipping confirmations to the Central office consistently throughout the day. The Phoenix remote office consists of one salesperson traveling through the southwest territory. The salesperson occasionally needs to connect to the Central office for e-mail access. How should the network administrator connect the remote sites to the Central office? (Choose two.)
*Connect to the Atlanta and Orlando remote offices with Frame Relay connections.
Connect to the Atlanta and Orlando remote offices with ISDN connections.
Connect to the Atlanta and Orlando remote offices with POTS dial-up connections.
Connect to the Phoenix remote office with a Frame Relay connection.
*Connect to the Phoenix remote office with a POTS dial-up connection.
7
A system administrator needs to configure the regional office with ISDN for DDR connections to three remote sites. Each remote site requires different IP subnets, different encapsulations, and different authentication methods. The sites will not be connected at the same time. The company would like to accomplish this in the most cost effective manner. What method can the system administrator use to accomplish this task using the fewest B channels?
Install and configure a PRI.
Install and configure a BRI interface with separate SPIDs for each remote site.
Install and configure a BRI with multiple switch types in global configuration.
*Install and configure a BRI using dialer profiles.
Install and configure a separate BRI for each remote site.
8
A network administrator is having difficulty in establishing a serial link between a Cisco router and a router from another vendor. Both routers are configured for HDLC encapsulation. Which statements are true regarding this configuration? (Choose two.)
*The Cisco HDLC frame uses a proprietary "Type" field that may not be compatible with equipment of other vendors.
HDLC requires a clock rate to be configured on the routers at both ends of the serial link.
*PPP encapsulation is recommended for serial links between equipment from multiple vendors.
Usernames must be configured at both ends of the HDLC serial link.
The HDLC vendor type must be enabled on the Cisco router.
There is a mismatch in the HDLC authentication password configurations.
9
Which of the following is the order for the three phases of establishing a PPP serial link with authentication?
authentication, link-establishment, network layer protocols
authentication, network layer protocols, link-establishment
network layer protocols, link-establishment, authentication
network layer protocols, authentication, link-establishment
*link-establishment, authentication, network layer protocols
link-establishment, network layer protocols, authentication
10
Refer to the exhibit. The link between the CTRL and BR_1 routers is configured as shown in the exhibit. Why are the routers unable to establish a PPP session?
The CHAP passwords must be different on the two routers.
The clock rate must be 56000.
Interface serial 0/0 on CTRL must connect to interface serial 0/1 on BR_1.
The IP addresses are on different subnets.
*The usernames are misconfigured.
The clock rate is configured on the wrong end of the link.
11
The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue will prevent IP traffic from crossing this link?
The passwords must be different for the CHAP authentication.
The usernames are misconfigured.
The clock rate must be 56000.
The clock rate is configured on the wrong end of the link.
*The IP addresses must be on the same subnet.
Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
12
A technician enters the interface serial 0/0.1 multipoint command when configuring a router. What effect will the multipoint keyword have in this configuration? (Choose two.)
*Split-horizon issues will need to be resolved for this network if RIP is the routing protocol.
A subinterface will be defined for each PVC.
*All the participating interfaces of remote routers will be configured in the same subnet.
A single DLCI will be used to define all the PVCs to the remote routers.
An IP address will need to be configured on the main interface.
13
Refer to the exhibit. A technician is configuring router Corp-1 to connect to router Corp-2 across the network shown in the graphic. Which router command will associate a Layer 2 address with the corresponding Layer 3 address in order to provide connectivity between the two routers?
Corp-1(config-if)# dialer-map ip 198.18.10.249 205 broadcast
Corp-1(config-if)# dialer-map 198.18.10.249 105 serial 0 broadcast
Corp-1(config-if)# dialer-map 198.18.10.250 inverse-arp broadcast
Corp-1(config-if)# frame-relay pvc 205 198.18.10.250
*Corp-1(config-if)# frame-relay map ip 198.18.10.250 205 broadcast
Corp-1(config-if)# frame-relay dlci 105 198.18.10.249 broadcast
14
Two routers are connected through a Frame Relay, point-to-point PVC. The remote router is from a vendor other than Cisco. Which interface command is required to configure the link between the Cisco router and the other router?
frame-relay pvc multipoint
frame-relay pvc point-to-point
encapsulation frame-relay cisco
*encapsulation frame-relay ietf
frame-relay lmi-type ansi
15
The command show frame-relay map gives the following output: Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status defined, active Which statements represent what is shown?(Choose two.)
*192.168.151.4 represents the IP address of the remote router.
192.168.151.4 represents the IP address of the local serial interface.
DLCI 122 represents the interface of the remote serial interface.
*DLCI 122 represents the local number used to connect to the remote address
broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC.
active indicates that the ARP process is working
16
The output of the show interfaces serial 0/0 command for a frame-relay connection indicates that the serial line is up but the line protocol is down. What are possible causes for this? (Choose two.)
*There is an LMI-type mismatch between the Frame Relay switch and the router.
*There is no clock present on the serial interface.
The interface is shut down.
RARP is not functioning on the router.
The cable is disconnected.
17
What can be done to Frame Relay to resolve split-horizon issues? (Choose two.)
Disable Inverse ARP.
*Create a full-mesh topology.
Develop multipoint subinterfaces.
*Configure point-to-point subinterfaces.
Remove the broadcast keyword from the frame-relay map command.
18
What does the status inactive indicate in the output of the show frame-relay pvc command?
*The DLCI is programmed in the switch but is not usable.
The DLCI was formerly programmed in the switch but is no longer there.
The DLCI is usable but has little activity.
The DLCI has been renamed for that PVC.
19
What can occur when a Frame Relay switch detects its queue filling faster than it can process data? (Choose two.)
Frames in excess of the CIR are not accepted by the switch.
*Frames with the DE bit set are dropped from the switch queue.
Frames with the FECN and BECN bits set are dropped from the switch queue.
*The switch sets the FECN bit on all frames it receives on the congested link and sets the BECN bit on all frames it places on the congested link.
The switch sets the FECN bit on all frames it places on the congested link and sets the BECN bit on all frames it receives on the congested link.
20
Which of the following are valid steps for a basic ISDN BRI configuration? (Choose two.)
create subinterfaces
define the LMI type
*set the SPIDs if required by the ISDN switch
set the interface DLCI
*set the switch type
specify the encapsulation as either Cisco or IETF
21
After the ISDN BRI interface is configured, which command can be used to verify that the router is communicating correctly with the ISDN switch?
show dialer
*show isdn status
show interfaces bri0/0:1
show interfaces serial0/0.1
22
Which ISDN protocol is specifies the data-link processes of LAPD?
ITU-T I.430
ITU-T I.431
*ITU-T Q.921
ITU-T Q.931
23
Which protocol should be chosen to support WAN connectivity in a multi-vendor system and provide strong security through authentication?
NAT with DHCP
Frame Relay
HDLC with encryption
HDLC with CHAP
PPP with PAP
*PPP with CHAP
24
Which of the following describes the roles of devices in a WAN? (Choose three.)
*A CSU/DSU terminates a digital local loop.
A modem terminates a digital local loop.
A CSU/DSU terminates an analog local loop.
*A modem terminates an analog local loop.
*A router is commonly considered a DTE device.
A router is commonly considered a DCE device.
25
When configuring a Frame Relay connection, when should a static Frame Relay map be used? (Choose two.)
when the remote router is a non-Cisco router
*when the remote router does not support Inverse ARP
when the local router is using IOS Release 11.1 or earlier
*when broadcast traffic and multicast traffic over the PVC must be controlled
when globally significant rather than locally significant DLCIs are being used
26
The exhibit represents steps to initiate a DDR call. Which option lists the steps in the proper order?
1,3,2,4
2,3,1,4
*2,3,4,1
3,4,1,2
4,1,3,2
4,2,3,1
27
What causes a DDR call to be placed?
dial string
DLCI
idle time out
*interesting traffic
PVC
28
After configuring a dialup ISDN circuit, a network associate begins testing the dialup connection. When attempting to ping a host on the remote network, the local router does not attempt to dial the remote access server. Which of the following are possible errors in this configuration? (Choose three.)
PPP authentication is not properly configured.
*No dialer map is configured.
The ISDN circuit connected to the remote access server is busy.
*No interesting traffic is defined.
*No route is determined to the remote network.
A wrong number is configured in the dial string.
29
A branch office reports excessive connect time charges for an ISDN circuit used to connect to the regional office. Upon investigation of this issue, it is discovered that when an ISDN connection is initiated to the regional office it remains connected for an excessive amount of time. Which of the following configuration changes could be made to DDR on the router to reduce these connect time charges?
use PPP multilink
*lower idle timer setting
use CHAP authentication
change DDR from legacy to dialer profiles
30
An ISDN circuit from a branch office is remaining connected to the regional office. A network administrator determines a user has initiated a continuous ping from a desktop computer to the regional office. Which configuration change would allow the ISDN circuit to disconnect during any attempts to ping, while otherwise functioning properly?
change DDR from legacy to dialer profiles
remove the dialer list statement from the configuration
*change the dialer list to exclude ICMP as interesting
disable inverse ARP
31
What value in the address field of a Frame Relay header identifies the destination of the frame?
CIR
DE
*DLCI
ISDN
FRAD
PVC
32
A network technician determines DHCP clients are not working properly. The clients are receiving IP configuration information from a DHCP server configured on the router but cannot access the Internet. From the output in the graphic, what is the most likely problem?
The DHCP server service is not enabled.
The inside interface for DCHP is not defined.
The DHCP pool is not bound to the interface.
*The pool does not have a default router defined for the clients.
All the host addresses have been excluded from the DHCP pool.
33
Which WAN technology is built on a cell-based rather than a frame-based architecture?
ISDN
Frame Relay
X.25
*ATM
34
A system administrator is troubleshooting a connectivity issue between two routers in a new installation. The administrator enters the debug ppp authentication command on the WHSE router. The graphic shows a part of the output received. From this output, what is the most likely cause of this connectivity issue?
There is not a route to the remote router.
The ISDN circuit on the remote router has failed.
*The username/password was not properly configured on the WHSE router.
The remote router has a different authentication protocol configured.
35
Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
*192.168.146.0/22
172.10.25.0/16
*172.31.0.0/16
20.0.0.0/8
*10.172.92.8/29
36
What functionality do access control lists provide when implementing dynamic NAT on a Cisco router?
defines which addresses are excluded from the NAT pool
defines which addresses are assigned to a NAT pool
defines which addresses are allowed out of the router
*defines which addresses can be translated
37
Given the partial router configuration in the graphic, why does the workstation with the IP address 192.168.1.153/28 fail to access the Internet? (Choose two.)
*The NAT inside interfaces are not configured properly.
The NAT outside interface is not configured properly.
*The router is not properly configured to use the access control list for NAT.
The NAT pool is not properly configured to use routable outside addresses.
The access control list does not include the IP address 192.168.1.153/28 to access the Internet.
38
Which statements describe NAT? (Choose two.)
*NAT hides the internal IP addressing structure from untrusted networks and conserves routable addresses.
Only one pool of routable addresses can be assigned per router interface.
*NAT can cause applications that depend on addressing, rather than domain names, to fail to function properly.
Cisco IOS NAT supports important protocols such as ICMP, FTP, BOOTP, and SNMP.
When using dynamic NAT, the number of hosts that can access the outside network is limited to the number of private addresses in the NAT pool.
39
How are the settings for ISDN switch type and SPIDs determined for a BRI interface configuration?
assigned by the network administrator
randomly, so long as they are not duplicated on the network
by trial and error
dynamically via Inverse ARP
assigned by IANA
*assigned by the service provider
40
When configuring a Frame Relay network with subinterfaces, which commands are configured on the subinterface? (Choose three.)
*frame-relay interface-dlci
encapsulation frame-relay ietf
*ip address
*frame-relay map
switch type ASasAS thanks look look 谢谢啦。不知道有没有ccna3 v.4的啊 再次多谢，我下载了哦 merci ~ 感谢楼主 ～～～～～ 感谢楼主 感 谢楼主 多谢 多谢 有没有第四期的啊 可以啊 怎么下载 哎 nengxiale 发射点发射点发射点 wokao!ding
页:
[1]