begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Sun Mar 2 2003, 09:53:37
!
#version 5.4(2)
!
!
#system web interface version Engine: 5.1 ADP device: Cat6000 ADP Version: 1.2 ADK: 31
!
set password $2$kHC1$ccKYMcXYRNrQY5qSPwMwh0
set enablepass $1$kGF1$NeLjpNFWh.7DAYRONDwgu/
!
#system
set system name!
#!
#snmp
set snmp community read-write-all khljk
!
#vtp
set vtp domain gjhgj
set vtp pruning enable
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 2 name ld type ethernet mtu 1500 said 100002 state active
set vlan 3 name ys type ethernet mtu 1500 said 100003 state active
set vlan 4 name gk type ethernet mtu 1500 said 100004 state active
set vlan 5 name ts type ethernet mtu 1500 said 100005 state active
set vlan 6 name kg type ethernet mtu 1500 said 100006 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#ip
set interface sc0 1 15.17.1213.253/255.255.255.0 15.17.1.255
set ip route 0.0.0.0/0.0.0.0 15.17.123.250
!
#spantree
#vlan 1
set spantree disable 1
#vlan 2
set spantree disable 2
#vlan 3
set spantree disable 3
#vlan 4
set spantree disable 4
#vlan 5
set spantree disable 5
#vlan 6
set spantree disable 6
#vlan 1003
set spantree disable 1003
#vlan 1005
set spantree disable 1005
!
#set boot command
set boot config-register 0x102
set boot system flash bootflash:cat6000-supcv.5-4-2.bin
!
#protocolfilter
set protocolfilter enable
!
#port channel
set port channel 3/1-4 2
set port channel 3/5-8 3
set port channel 2/5-8 6
set port channel 2/9-12 7
set port channel 2/13-16 8
set port channel 2/17-20 9
set port channel 2/21-24 10
set port channel 2/25-28 11
set port channel 2/29-32 12
set port channel 2/33-36 13
set port channel 2/37-40 14
set port channel 2/41-44 15
set port channel 2/45-48 16
set port channel 2/1-4 677
!
#http configuration
set ip http server enable
!
# default port status is enable
!
!
#module 1 : 2-port 1000BaseX Supervisor
!
#module 2 : 48-port 10/100BaseTX Ethernet
set vlan 2 2/5-26
set vlan 3 2/27-36
set vlan 4 2/37-42
set port speed 2/35-36 10
set port speed 2/7,2/11 100
set port duplex 2/7,2/11,2/35-36 full
set port name 2/13 041006
set port protocol 2/47 ipx off
set trunk 2/1 on isl 1-1005
set trunk 2/2 on isl 1-1005
set trunk 2/3 on isl 1-1005
set trunk 2/4 on isl 1-1005
set port channel 2/1-4 mode on
!
#module 3 : 8-port 1000BaseX Ethernet
set trunk 3/1 on isl 1-1005
set trunk 3/2 on isl 1-1005
set trunk 3/3 on isl 1-1005
set trunk 3/4 on isl 1-1005
set trunk 3/5 on isl 1-1005
set trunk 3/6 on isl 1-1005
!
#module 4 empty
!
#module 5 empty
!
#module 6 empty
!
#module 15 : 1-port Multilayer Switch Feature Card
!
#module 16 empty
end
[ 本帖最后由 80798207 于 2006-5-25 17:26 编辑 ]
社区：
