tangziwen
新新人类
帖子
6
精华
0
无忧币 1
积分 24
阅读权限 20
|
发表于:2008-3-21 22:58
标题：发一份详细的华为3526配置命令。
＜上一帖 |
下一帖＞
使用超级终端登陆 COM3口 9600 8 无 1 N
对交换机顺序作如下配置
quidway > sup (进入特权模式)
Now user privilege is 3 level, and just commands which level is
equal to or less than this level can be used.
Privilege note: 0-VISIT, 1-MONITOR, 2-SYSTEM, 3-MANAGE
quidway > sys (进入配置模式)
Enter system view, return to user view with Ctrl+Z.
// 配置上行口数据
[ quidway ] interface Ethernet 0 /1 （进入接口配置模式0/1口）
[ quidway- Ethernet 0 /1] port link-type trunk （设置0/1口为中继模式，该端口上行和汇聚设备对接）
[ quidway- Ethernet 0 /1] port trunk permit vlan all （允许所有VLAN通过该端口）
[ quidway- Ethernet 0 /1] quit （退出接口模式）
// 为各个端口配置VLAN
[ quidway ] vlan 2 （创建vlan 2）
[ quidway-vlan2 ] int erface Ethernet 0/2 (进入接口配置模式)
[ quidway- Ethernet 0 / 2 ] port access vlan 2 (把0/2口划入vlan 2)
[ quidway- Ethernet 0 / 2 ] vlan 3 （创建vlan 3）
[ quidway-vlan3 ] int erface Ethernet 0 / 3 (进入接口配置模式)
[ quidway- Ethernet 0 / 3 ] port access vlan 3 (把0/3口划入vlan 3)
[ quidway- Ethernet 0/3 ] vlan 4
[ quidway-vlan4 ] int erface Ethernet 0/4
[ quidway- Ethernet 0 / 4 ] port access vlan 4
[ quidway- Ethernet 0/4 ] vlan 5
[ quidway-vlan5 ] int erface Ethernet 0 / 5
[ quidway- Ethernet 0/5 ] port access vlan 5
[ quidway- Ethernet 0/5 ] vlan 6
[ quidway-vlan6 ] int erface Ethernet 0 / 6
[ quidway- Ethernet 0/6 ] port access vlan 6
[ quidway- Ethernet 0/6 ] vlan 7
[ quidway-vlan7 ] int erface Ethernet 0/7
[ quidway- Ethernet 0 / 7 ] port access vlan 7
[ quidway- Ethernet 0/7 ] vlan 8
[ quidway-vlan8 ] int erface Ethernet 0 / 8
[ quidway- Ethernet 0/8 ] port access vlan 8
[ quidway- Ethernet 0/8 ] vlan 9
[ quidway-vlan9 ] int erface Ethernet 0 / 9
[ quidway- Ethernet 0/9 ] port access vlan 9
[ quidway- Ethernet 0/9 ] vlan 10
[ quidway-vlan10 ] int erface Ethernet 0/10
[ quidway- Ethernet 0 / 10 ] port access vlan 10
[ quidway- Ethernet 0/10 ] vlan 11
[ quidway-vlan11 ] int erface Ethernet 0 / 11
[ quidway- Ethernet 0/11 ] port access vlan 11
[ quidway- Ethernet 0/11 ] vlan 12
[ quidway-vlan12 ] int erface Ethernet 0 / 12
[ quidway- Ethernet 0/12 ] port access vlan 12
[ quidway- Ethernet 0 / 12 ] quit
// 配置远程管理VLAN
[ q uidway ] vlan 2050 (创建VLAN 2050 ，)
[ quidway ] Vlan-interface20 50 (进入VLAN接口配置模式)
[ quidway- Vlan-interface20 50] ip address ip地址 255.255.252.0 （配置管理VLAN接口2050的IP地址为：你分配给设备的ip地址 子网掩码为：255.255.252.0）
[ quidway- Vlan-interface20 35] quit （退出VLAN接口配置模式）
// 配置远程登陆口令
[ quidway ] ip route-static 0.0.0.0 0.0.0.0 网关ip (配置网关)
[ quidway ] super password level 3 cipher worp09 （配置特权模式口令为“worp09 ” ）
[ quidway ] user-interface vty 0 4 （打开TELNET服务功能）
[ quidway- ui-vty0-4] set authentication password cipher worp09 (设置TELNET口令为“worp09”)
[ quidway- ui-vty0-4] quit （退出）
[ quidway ] quit
// 配置完毕，保存配置
save (保存配置)
This will save the configuration in the flash memory.
The switch configurations will be written to flash.
Are you sure?[Y/N] y
Now saving current configuration to flash memory.
Please wait for a while...
Current configuration saved to flash memory successfully.
(完) 华为设备管理的朋友可以加我qq：306934961.一起讨论学习。
[ 本帖最后由 tangziwen 于 2008-3-21 22:59 编辑 ]
|
千里之外，传递你对震灾人民的关怀 |
|
| 诚征版主 | 版主堂 | 意见建议 | 大史记 | 论坛地图